Milk Cooling Tank
Milk Reception Unit
Capacity
2000 lt, 3000 lt, 4000 lt, 5000 lt, 6000 lt, 8000 lt, 10000 lt, 12000 lt, 15000 lt
construction
It is completely AISI 304 quality stainless steel.
The 1st wall base is 2 mm and there is a 0.8 mm Ep type rollbond heat exchanger plate coupled to the wall.
The insulated wall is 1.5 mm in 2-3 tons tanks and 2 mm AISI 304 quality stainless steel in 4-15 tons tanks.
There is one specially designed 0.34 Hp 33 rpm gearbox and associated stainless steel mixer blades. The mixer wing is designed not to spoil the milk structure.
(There are 2 mixer in 6000 lt, 8000 lt, 10000 lt, 12000 lt and 15000 lt.)
Product outlet DN 50 male butterfly valve.
Insulation range is 60 mm thick and isolated with water based high dense polyurethane foam material without HCFC.
AISI 304 quality stainless steel Ø 500 mm, manhole cover and Ø 100 mm product inlet.
There is a special manual ruler for each tank with a calculation table. (‰ It has 3-4 sensitivity ratio.)
There is 1 stainless steel (non-slip) ladder on the tank.
Ø 90 ventilation grilles are available.
Adjustable feet in AISI 304 quality stainless steel
It is designed to remain zero liquid inside.
The tank body was coupled on the solid chassis.
Welded areas are 1st class Argon TIG welding and 1st class smooth polished.
The cooler evaporator (rollbond) was subjected to a test pressure of 40 bar.
Cooling Group
Minimum amount of gas charge
A 404 gas cooled
Cooling opportunity without icing even in low milk quantity
Each milking (38 ° C – 43 ° C) provides cooling opportunity under ambient temperature from 35 ° C to 4 ° C under 3 hours. You can also see the class that each tank has entered by examining the Experiment Compliance Report owned by our company.
Each refrigerant compressor has (Dryer, sight glass, expansion valve, solenoid valve, liquid trap and valves).
Cooling compressors are coupled to the solid chassis on the tank.
Electronic Control Board
The electronic control system is coupled into the stainless steel panel and all transactions are carried out on the electronic control card of Kromel company.
On the control control panel, the operation of the tank, milk temperature, electronic milk measurement, washing system and menus are controlled from here.
In case of electronic system failure, cooling process can be continued by taking the manual position.
There is an additional electromechanical safety system set to 1.5 – 2 ° C to prevent milk from freezing.
It gives an error message about the fault that occurs in case of any fault.
It is possible to see the malfunctions, washing temperature, milk temperature and electrical malfunctions occurring in the last 20 days.
Compressors are activated gradually to prevent sudden current draw in multi system compressors.
Phase protection relay is available.
The electronic control panel has outputs that can be connected to the internet.
Thanks to the special software automatic mixing program, the working intervals of the mixer can be adjusted after the coldness of the milk reaches the desired set value. (Such as working for 3 minutes and stopping for 10 minutes)
It has IP 65 protection standard.
Automatic Washing
Water penetration to the entire surface thanks to the specially designed CIP ball
Washing program at the touch of a button Low detergent consumption
Detergent dosing pump as an option
Digital Level Indicator
‰ It has the opportunity to measure with 0-2 error margin.
The amount of milk in the tank can be monitored on the control panel.
The amount of milk in the tank can show in mm, kg, and lt.
Capacity
300 Lt – 500 Lt – 1000 Lt – 1500 Lt – 2000 Lt
construction
It is AISI 304 quality stainless steel.
The 1st wall base is 2 mm and there is a 0.8 mm Ep type rollbond heat exchanger plate coupled to the wall.
1st body is 1.5 mm.
The insulated wall is 1 mm AISI 304 quality stainless steel.
There is 1 25 W 21 d / d reducer and stainless steel mixer blades connected to it. The mixer wing is designed not to spoil the milk structure.
Product outlet DN 50 male butterfly valve.
Insulation range is 50 mm thick and isolated with HCFC-free water-based high-dense polyurethane foam material.
There is a spring lid system and a product entrance with Ø 200 mm lid on the lid.
There is a special manual ruler for each tank. (Hassasiyet It has 3-4 sensitivity rates.)
It is designed to remain zero liquid inside.
The tank body was coupled on the solid chassis.
Welded areas are 1st class Argon TIG welding and 1st class smooth polished.
The cooler evaporator (rollbond) was subjected to a test pressure of 40 bar.
Cooling Group
Minimum amount of gas charge
A 404 gas cooled
Cooling opportunity without icing even in low milk quantity
Each milking (38 ° C – 43 ° C) provides cooling opportunity under ambient temperature from 35 ° C to 4 ° C under 3 hours. You can also see the class that each tank has entered by examining the Experiment Compliance Report owned by our company.
Each refrigerant compressor has (Dryer, sight glass, expansion valve, solenoid valve, liquid trap and valves).
Cooling compressors are coupled to the solid chassis on the tank.
Electronic Control Board
The electronic control system is coupled to the special panel, and all transactions are made on the electronic control card of Kromel company.
On the control control panel, the tank is operated and the milk temperature is controlled.
Phase protection relay is available.
The system (reducer and cooling) is automatically disabled when the tank cover is opened.
Thanks to the special software automatic mixing program, the working intervals of the mixer can be adjusted after the coldness of the milk reaches the desired flood value. (Such as working for 3 minutes and stopping for 10 minutes)
Option
Digital Level Indicator
It has the opportunity to measure with a margin of 0- ‰ 2.
The amount of milk in the tank can be monitored on the control panel.
It can show the amount of milk in the tank in mm, kg and lt.